Penerbit: Jurusan Teknik Pertanian FP UNILA
P-ISSN:
E-ISSN: 28304403
DOI: http://dx.doi.org/10.23960/jabe
Fakultas Pertanian Umum Arsitektur
Artikel (228)
Performance Test of Hotong Seed Billing Machine (Setaria italica (L.) P. Beauv) Abrasive Roll Type with Grinding Stone
Indonesia has a lot of diversity, one of which is in food. Carbohydrates are basic food needs that must be met, in Indonesia there is the potential for various alternative foods. One of the alternative food ingredients producing carbohydrates is hotong. Hotong is a plant that is often found in Indon...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 438-449 | 2023
Pengaruh Pola Pengolahan Terhadap Efisiensi Pengolahan Tanah Menggunakan Traktor Tangan
 It is important to choose a tillage pattern with the aim of efficiency and effectiveness. This research aims to analyze the effect of tillage patterns using hand tractors on processing work capacity, processing time efficiency and fuel requirements. The research was conducted at the BPTP Lampung N...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 450-460 | 2023
Pengaruh Kecepatan Putar dan Jumlah Masukan Batang Singkong Terhadap Kinerja Mesin Rabakong Tipe TEP-6
Cassava production not only produces tubers, but also produces waste, one of which is cassava stems. So far, the waste of cassava stems has not been widely used by farmers, so that after the cassava is harvested, the cassava stems are just left lying on the ground. This study aims to reduce cassava ...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 470-476 | 2023
Pengaruh Jumlah Masukan dan Varietas Batang Singkong Terhadap Kinerja Mesin Rabakong Tipe TEP-6
A lot of cassava stem waste is not used and is only left to rot or burned, so the handling of cassava stems into animal feed ingredients is carried out. The purpose of this research is to determine the performance of the TEP-6 type cassava stem chopper in carrying out the shrinking process with the ...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 428-437 | 2023
Optimasi Ukuran Pot dan Dosis Pupuk pada Budidaya Melon (Cucumis melo L)
This research aimed to determine the optimum pot size and fertilizer dosage for melon (Cucumis melo L) cultivation based on productivity. The experiment used a Completely Randomized Design (CRD) arranged factorially with 2 factors and two replicates. The first factor was the dose of compost fertiliz...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 419-427 | 2023
Pengaruh Variasi Bahan Peredam Kemasan dan Tingkat Kematangan Buah Alpukat terhadap Tingkat Kerusakan Mekanis pada Simulasi Getaran Selama Transportasi
Cause of damage is improper or inappropriate packaging. Therefore this study aims to determine the optimal type of packaging damper in minimizing mechanical damage to the fruit. This research was conducted in February - April 2020 at the Laboratory of Bioprocess Engineering and Postharvest Handling,...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 410-418 | 2023
Modifikasi Alat Perajang Batang Singkong (Rabakong Tipe Tep 5) untuk Meningkatkan Kapasitas Kerja
Lampung Province is the largest producer of cassava in Indonesia. However, cassava production in Lampung has been declining over the past five years due to many farmers switching to other commodities due to the long harvesting period and unstable prices. This has resulted in a buildup of cassava ste...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 399-409 | 2023
Mempelajari Pembuatan Tepung dari Buah Pepaya sebagai Bahan Baku Makanan
Papaya is one of the fruits that are liked in the community because of it has a sweet taste and rich in vitamin C. In Indonesia papaya is abundant and the price of it is relatively low so that papaya gets wasted easily.  Therefore, it is necessary to process the product to extend the shelf life and...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 393-398 | 2023
Analisis Ergonomika Pengoperasian Bagian Pencacah pada Mesin Pencacah Pakan Ternak Multiguna
The multi-purpose animal feed chopping machine is one of the feed chopping tools that many farmers use to help speed up the chopping of raw materials that will be used as animal feed. The chopping machine can be operated optimally if the machine is ergonomic so that it is safe and comfortable to ope...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 383-392 | 2023
Pengaruh Sinar UV-C terhadap Perubahan Mutu Wortel (Daucus carota L.) Selama Penyimpanan
Based on the survey result of vegetable crop production in Indonesia, the national carrot harvest area is 13,398 hectares spread over 16 provinces.  Meanwhile, the average carrot production in Lampung Province can reach 16,02 tons/year with a harvested area of 369 hectares (BPS, 2018).  Damage to ...
Jurnal Agricultural Biosystem Engineering; Vol. 2 No. 3 (2023): September 2023; 361-372 | 2023